Aiming and Focusing

From NaturalPoint Product Documentation
Jump to: navigation, search
Back to the Main PageBack to Hardware Setup


In order to ensure that every camera in the system takes full advantage of its capability, they need to be properly focused and aimed at their target subject(s). This page includes detailed instructions on how to adjust the focus and aim of each camera for an optimal motion capture session. OptiTrack cameras are focused at infinity by default, which means that they are set to track from distances as near as a few feet away up to their maximum tracking range, and therefore, adjusting camera focus will not be needed for most common applications. However, for very close-up configurations (e.g. tracking markers from 1-4’ away from cameras), tracking quality and image clarity can be improved by adjusting the focus of the camera lens.


Steps in adjusting focus and aiming

  1. Make sure that the camera placement is appropriate for your application.
  2. Pick a camera to adjust the aim and focus.
  3. Set the camera to the raw grayscale video mode (in Motive) and increase the camera exposure to capture the brightest image (These steps are accomplished by the Aim Assist Button on featured cameras).
  4. Place one or more reflective markers in the tracking volume.
  5. Carefully adjust the camera angle while monitoring the Camera Preview so that the desired capture volume is included within the camera coverage.
  6. Within the Camera Preview in Motive, zoom in on one of the markers so that it fills the frame.
  7. Adjust the focus (detailed instruction given below) so that the captured image is resolved as clearly as possible.
  8. Repeat above steps for other cameras in the system.


Aim Assist Button



Adjusting aim with a single person can be difficult because the user will have to run back and forth from the camera and the host PC in order to adjust the camera angle and monitor the 2D view at the same time. OptiTrack cameras featuring the Aim Assist button (Prime series and Flex 13) makes this aiming process easier. With just one button-click, the user can set the camera to the grayscale mode and the exposure value to its optimal setting for adjusting both aim and focus. Fit the capture volume within the vertical and horizontal range shown by the virtual crosshairs that appear when Aim Assist mode is on. With this feature, the single-user no longer needs to go back to the host PC to choose cameras and change their settings. Settings for Aim Assist buttons are available from Application Settings pane.


Adjusting Aiming



Cameras — shows only one side — aimed to cover the main target volume

After all the cameras are placed at correct locations, they need to be properly aimed in order to fully utilize its capture coverage. In general, all cameras need to be aimed at the target capture volume where markers will be tracked. While cameras are still attached to the mounting structure, carefully adjust the camera clamp so that the camera field of view (FOV) is directed at the capture region. Refer to 2D camera views from the Camera Preview pane, and ensure that each camera view covers the desired capture region.


FnA AimAssist.png


Adjusting Focus



All OptiTrack cameras (except the V120:Duo/Trio tracking bars) can be re-focused to optimize image clarity at any distance within the tracking range. Change the camera mode to raw grayscale mode and adjust the camera setting, increase exposure and LED setting, to capture the brightest image. Zoom into one of the reflective marker in the capture volume and check clarity of the image. Then, adjust the camera focus and find the point where the marker image is best resolved. The following images show some examples.


FnA InFocus.png


How to Change Focus


Flex series

Flex series cameras use M12 lenses. The camera focus is adjusted by rotating the lens body, and the camera lens needs to be exposed in order to adjust the focus. For Flex 3 cameras, unscrew the three hex screws located on the back and carefully remove the front housing. Flex 13 cameras, unscrew the two hex key screws and pull on the front housing while the case release button is pressed. The two hex screws are optional and the housing can be secured without them for easy access. The following diagram describes how to remove the housing in Flex 13 camera models. Note that the LED array will not be functional when the housing is removed, and the Flex 13 camera will rely on the LED illumination from other cameras while adjusting the focus.


Removing front housing of a Flex 13 camera.


Prime 13 and 13W

Prime 13 and Prime 13W use M12 lenses and cameras can be focused using custom focus tools to rotate the lens body. Focusing tools can be purchased on OptiTrack’s Lens Accessories page, and they clip onto the camera lens and rotates it without opening the camera housing. It could be beneficial to lower the LED illumination to minimize reflections from the adjusting hand.


  • Focus tool for Prime 13
  • Focus tool for Prime 13W.


Prime 17W and 41

For Prime 17W and 41 models, camera focus can be adjusted by manually rotating the focus ring on the lens body, which can be accessed at the center of the camera. The front ring of the lens changes the lens aperture size. Set the aperture at its maximum size in order to capture the brightest image. The focus ring is located on the rear of the lens body. Carefully rotate the focus ring while monitoring the 2D grayscale camera view for image clarity. Align the mark with the infinity symbol when setting the focus back to infinity. Once the focus has been optimized, it should be locked down by tightening the set screw.


Prime 41 (F#1.8) and Prime 17 (F#1.6) lenses


Slim Series

Slim 13E cameras also feature M12 lenses. The camera focus can be easily adjusted by rotating the lens without the need to remove the housing. Slim 3U cameras are customizable. They support multiple lens types, including third-party lenses so focus techniques will vary. Refer to the lens type to determine how to proceed. (In general, M12 lenses will be focused by rotating the lens body, while C and CS lenses will be focused by rotating the focus ring).

Slim 3U assembly.



Back: Cabling and Wiring

Next: Motive Documentation